A Step-by-Step Guide to Setting Up a Tub
A Step-by-Step Guide to Setting Up a Tub
Blog Article
The content below on the subject of A Step-by-Step Guide to Installing a Bathtub is fairly engaging. Don't miss it.
Mounting a tub isn't exactly rocket science, yet it does need solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bath tub with a new one is additionally a reasonably tough project. If the old tub is conveniently accessible, the task can relocate immediately; if you have to open a wall surface to eliminate the old tub and also place the new bathtub, the job is much harder. In either case, the job is within a house handyman's skills, although you will certainly need a helper to leave the old bathtub as well as set in the brand-new one. Make certain you have actually certified yourself for the work as well as are comfortable trying it. Instead of hiring a service provider to take over a halfway-completed project, it is far better to think about using one before you start. Possibilities are you may require a professional plumber to make tube links.
This short article will aid you mount a new bath tub in your restroom if you have actually already acquired a new bathtub and do not need to alter the arrangement of your previous supply of water pipelines.
Your tools and also material list should make up the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is detach the water. After doing so, switch on the faucets to drain pipes any water staying in the system. The procedure of removing the existing faucets can be fairly bothersome because of the limited access that is commonly the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a fabric ready for the remaining water that will originate from the pipes. Once the supply pipelines have actually been removed, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming during this procedure. Once the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Before going on to fit the new taps, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and also the other end supplies a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin ensuring that the washers are in place between the faucet as well as the sink. Safeguard the faucet in place with the manufacturer offered backnut. When the faucet is safely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet adapters. The former type ought to be linked to the faucet finishes first, tightening only by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Bath tub
Making use of the two wooden boards under its feet, put the tub in the needed placement. The wood boards are helpful in evenly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto 4 little factors.
The next goal is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the tub up until the level checks out degree.
To set up faucets, fit all-time low of the outermost versatile faucet port to the proper supply pipeline by making a compression sign up with; then do the exact same for the other tap.
Switch on the supply of water and check all joints and brand-new pipework for leakages as well as tighten them if necessary. Fill the bath tub as well as likewise check the overflow electrical outlet and also the typical outlet for leaks.
Ultimately, take care of the bath paneling as defined in the maker's instruction manual. Tiling and securing around the tub ought to wait until the bath tub has been used at the very least when as this will resolve it right into its final placement.
Getting ready for the Installation
To start with, the supporting frame provided with the bath should be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to ensure that if the faucet includes a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets system to prevent stress on the bath tub.
Fit the versatile faucet ports to the bottom of both taps making use of 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet with the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you use all of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath must currently be ready to be fitted in its final setting.
Tiling Around the Bath tub
In the area where the bath satisfies the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to crack a stiff seal, triggering the water to permeate the wall surface in between the bathroom and the tiling, resulting in problems with moisture as well as possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and also fittings. They are sold in tubes and cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to load, you can load it with twists of soaked newspaper or soft rope. Remember to always fill the bathtub with water before sealing, to allow for the movement experienced when the tub remains in usage. The sealer can fracture rather very early if you do not think about this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently offered on the market. It is recommended to fit the tiles using water-resistant or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I found that entry about Tools You Need to Install a New Bathtub when scouting around the web. If you liked our post please don't forget to pass it around. I recognize the value of reading our article about A Step-by-Step Guide to Installing a Bathtub.
More Details
Report this page